| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix missing read bio submission on large folio error
f2fs_read_data_large_folio() can keep a read bio across multiple
readahead folios. If a later folio hits an error before any of its
blocks are added to the bio, folio_in_bio is false and the current error
path returns immediately after ending that folio.
This can leave the bio accumulated for earlier folios unsubmitted. Those
folios then never receive read completion, and readers can wait
indefinitely on the locked folios.
Route errors through the common out path so any pending bio is submitted
before returning. Stop consuming more readahead folios once an error is
seen, and only wait on and clear the current folio when it was actually
added to the bio. |
| The USB CDC-NCM device class (subsys/usb/device_next/class/usbd_cdc_ncm.c) ignores the return value of usbd_ep_enqueue() in its ethernet transmit callback cdc_ncm_send(). When the enqueue fails, the function still calls k_sem_take(&data->sync_sem, K_FOREVER), blocking on a completion semaphore that is only ever signaled from the bulk-IN transfer-completion callback. Because nothing was enqueued, that callback never fires and the calling thread — a shared network traffic-class TX thread — deadlocks permanently while holding the interface TX lock, halting transmission until reboot (and leaking the transmit buffer).
The enqueue fails under conditions controlled by the attached USB host: usbd_ep_enqueue() returns -EPERM whenever the bus is suspended (a standard, persistent host operation), and the underlying udc_ep_enqueue() returns -EPERM/-ENODEV on disconnect, bus reset, or endpoint disable. The cdc_ncm_send() guard only checks the DATA_IFACE_ENABLED and IFACE_UP flags, not the suspended state, so a packet transmitted while the host holds the bus suspended reaches the failing enqueue and deadlocks the TX path.
The realistic trigger is a bus suspend that occurs while the exported network interface is active and has traffic to send — host sleep, USB selective/auto-suspend, or hub power management — after which any device-originated packet deadlocks the path, recoverable only by reboot. The impact is a persistent loss of the virtual network connection between the host's NCM interface and the Zephyr device; because the deadlocked thread is a shared traffic-class TX thread, egress on other network interfaces can stall as well. There is no memory corruption or information disclosure.
The defect was introduced with the CDC-NCM driver and shipped in releases through v4.4.0; it is fixed by checking the usbd_ep_enqueue() return value and freeing the buffer before the blocking wait. |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't call fill_pool() in early boot hardirq context
When booting a debug PREEMPT_RT kernel on an ARM64 system, a "inconsistent
{HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage" lockdep warning message was
reported to the console.
During early boot, interrupts are enabled before the scheduler is
enabled. In this window (before SYSTEM_SCHEDULING is set) interrupts can
fire and in the hard interrupt context handler attempt to fill the pool
This can lead to a deadlock when the interrupt occurred when the interrupt
hits a region which holds a lock that is required to be taken in the
allocation path.
Add a new can_fill_pool() helper and reorder the exception rule and forbid
this scenario by excluding allocations from hard interrupt context. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix potential deadlock in mt7921_roc_abort_sync
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() -> mt7921_mac_sta_remove() ->
mt7921_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
slimbus: qcom-ngd-ctrl: Avoid ABBA on tx_lock/ctrl->lock
During the SSR/PDR down notification the tx_lock is taken with the
intent to provide synchronization with active DMA transfers.
But during this period qcom_slim_ngd_down() is invoked, which ends up in
slim_report_absent(), which takes the slim_controller lock. In multiple
other codepaths these two locks are taken in the opposite order (i.e.
slim_controller then tx_lock).
The result is a lockdep splat, and a possible deadlock:
rprocctl/449 is trying to acquire lock:
ffff00009793e620 (&ctrl->lock){+.+.}-{4:4}, at: slim_report_absent (drivers/slimbus/core.c:322) slimbus
but task is already holding lock:
ffff00009793fb50 (&ctrl->tx_lock){+.+.}-{4:4}, at: qcom_slim_ngd_ssr_pdr_notify (drivers/slimbus/qcom-ngd-ctrl.c:1475) slim_qcom_ngd_ctrl
which lock already depends on the new lock.
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ctrl->tx_lock);
lock(&ctrl->lock);
lock(&ctrl->tx_lock);
lock(&ctrl->lock);
The assumption is that the comment refers to the desire to not call
qcom_slim_ngd_exit_dma() while we have an ongoing DMA TX transaction.
But any such transaction is initiated and completed within a single
qcom_slim_ngd_xfer_msg().
Prior to calling qcom_slim_ngd_exit_dma() the slim_controller is torn
down, all child devices are notified that the slimbus is gone and the
child devices are removed.
Stop taking the tx_lock in qcom_slim_ngd_ssr_pdr_notify() to avoid the
deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gma500/oaktrail_lvds: fix hang on init failure
The LVDS init code looks up an I2C adapter using i2c_get_adapter() and
tries to read the EDID before falling back to allocating and registering
its own adapter.
The error handling does not separate these cases so on a late init
failure it will try to deregister and free also an adapter that had
previously been registered. Since i2c_get_adapter() takes another
reference to the adapter, deregistration hangs indefinitely while
waiting for the reference to be released.
Fix this by only destroying adapters allocated during LVDS init on
errors. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix AMDGPU_INFO_READ_MMR_REG
There were multiple issues in that code.
First of all the order between the reset semaphore and the mm_lock was
wrong (e.g. copy_to_user) was called while holding the lock.
Then we allocated memory while holding the reset semaphore which is also
a pretty big bug and can deadlock.
Then we used down_read_trylock() instead of waiting for the reset to
finish.
(cherry picked from commit 361b6e6b303d4b691f6c5974d3eaab67ca6dd90e) |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: fix ABBA deadlock in iptfs_destroy_state()
iptfs_destroy_state() calls hrtimer_cancel() while holding a spinlock
that the timer callback also acquires, leading to an ABBA deadlock on
SMP systems.
For the output timer (iptfs_timer):
- iptfs_destroy_state() holds x->lock, calls hrtimer_cancel()
- iptfs_delay_timer() callback takes x->lock
For the drop timer (drop_timer):
- iptfs_destroy_state() holds drop_lock, calls hrtimer_cancel()
- iptfs_drop_timer() callback takes drop_lock
Both timers use HRTIMER_MODE_REL_SOFT, so their callbacks run in softirq
context. When hrtimer_cancel() is called for a soft timer that is
currently executing on another CPU, hrtimer_cancel_wait_running() spins
on softirq_expiry_lock -- the same lock held by the softirq running the
callback. If the callback is blocked waiting for the spinlock held by
the caller of hrtimer_cancel(), a circular dependency forms:
CPU 0: holds lock_A -> waits for softirq_expiry_lock
CPU 1: holds softirq_expiry_lock -> waits for lock_A
Fix by calling hrtimer_cancel() before acquiring the respective locks.
hrtimer_cancel() is safe to call without holding any lock and will wait
for any in-progress callback to complete. For the output timer, the
lock is still acquired afterwards to drain the packet queue. For the
drop timer, the lock/unlock pair is removed entirely since it only
existed to serialize with the timer callback, which hrtimer_cancel()
already guarantees.
Found by source code audit. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memory-failure: fix hugetlb_lock AA deadlock in get_huge_page_for_hwpoison
Two concurrent madvise(MADV_HWPOISON) calls on the same hugetlb page can
trigger a recursive spinlock self-deadlock (AA deadlock) on hugetlb_lock
when racing with a concurrent unmap:
thread#0 thread#1
-------- --------
madvise(folio, MADV_HWPOISON)
-> poisons the folio successfully
madvise(folio, MADV_HWPOISON) unmap(folio)
try_memory_failure_hugetlb
get_huge_page_for_hwpoison
spin_lock_irq(&hugetlb_lock) <- held
__get_huge_page_for_hwpoison
hugetlb_update_hwpoison()
-> MF_HUGETLB_FOLIO_PRE_POISONED
goto out:
folio_put()
refcount: 1 -> 0
free_huge_folio()
spin_lock_irqsave(&hugetlb_lock)
-> AA DEADLOCK!
The out: path in __get_huge_page_for_hwpoison() calls folio_put() to drop
the GUP reference while the hugetlb_lock is still held by the hugetlb.c
wrapper get_huge_page_for_hwpoison(). If concurrent unmap has released
the page table mapping reference, folio_put() drops the folio refcount to
zero, triggering free_huge_folio() which attempts to re-acquire the
non-recursive hugetlb_lock.
Fix this by moving hugetlb_lock acquisition from the hugetlb.c wrapper
into get_huge_page_for_hwpoison(). Place spin_unlock_irq() before the
folio_put() at the out: label so the folio is always released outside the
lock.
[akpm@linux-foundation.org: fix race, rename label per Miaohe] |
| In the Linux kernel, the following vulnerability has been resolved:
md: wake raid456 reshape waiters before suspend
During raid456 reshape, direct IO across the reshape position can sleep
in raid5_make_request() waiting for reshape progress while still
holding an active_io reference. If userspace then freezes reshape and
writes md/suspend_lo or md/suspend_hi, mddev_suspend() kills active_io
and waits for all in-flight IO to drain.
This can deadlock: the IO needs reshape progress to continue, but the
reshape thread is already frozen, so the active_io reference is never
dropped and suspend never completes.
raid5_prepare_suspend() already wakes wait_for_reshape for dm-raid. Do
the same for normal md suspend when reshape is already interrupted, so
waiting raid456 IO can abort, drop its reference, and let suspend
finish.
The mdadm test tests/25raid456-reshape-deadlock reproduces the hang. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: return VMA snapshot from task_vma iterator
Holding the per-VMA lock across the BPF program body creates a lock
ordering problem when helpers acquire locks that depend on mmap_lock:
vm_lock -> i_rwsem -> mmap_lock -> vm_lock
Snapshot the VMA under the per-VMA lock in _next() via memcpy(), then
drop the lock before returning. The BPF program accesses only the
snapshot.
The verifier only trusts vm_mm and vm_file pointers (see
BTF_TYPE_SAFE_TRUSTED_OR_NULL in verifier.c). vm_file is reference-
counted with get_file() under the lock and released via fput() on the
next iteration or in _destroy(). vm_mm is already correct because
lock_vma_under_rcu() verifies vma->vm_mm == mm. All other pointers
are left as-is by memcpy() since the verifier treats them as untrusted. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix deadlock in remain-on-channel
mt76_remain_on_channel() and mt76_roc_complete() call mt76_set_channel()
while already holding dev->mutex. Since mt76_set_channel() also acquires
dev->mutex, this results in a deadlock.
Use __mt76_set_channel() instead of mt76_set_channel().
Add cancel_delayed_work_sync() for mac_work before acquiring the mutex
in mt76_remain_on_channel() to prevent a secondary deadlock with the
mac_work workqueue. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: usbhid: fix deadlock in hid_post_reset()
You can build a USB device that includes a HID component
and a storage or UAS component. The components can be reset
only together. That means that hid_pre_reset() and hid_post_reset()
are in the block IO error handling. Hence no memory allocation
used in them may do block IO because the IO can deadlock
on the mutex held while resetting a device and calling the
interface drivers.
Use GFP_NOIO for all allocations in them. |
| In the Linux kernel, the following vulnerability has been resolved:
greybus: gb-beagleplay: fix sleep in atomic context in hdlc_tx_frames()
hdlc_append() calls usleep_range() to wait for circular buffer space,
but it is called with tx_producer_lock (a spinlock) held via
hdlc_tx_frames() -> hdlc_append_tx_frame()/hdlc_append_tx_u8()/etc.
Sleeping while holding a spinlock is illegal and can trigger
"BUG: scheduling while atomic".
Fix this by moving the buffer-space wait out of hdlc_append() and into
hdlc_tx_frames(), before the spinlock is acquired. The new flow:
1. Pre-calculate the worst-case encoded frame length.
2. Wait (with sleep) outside the lock until enough space is available,
kicking the TX consumer work to drain the buffer.
3. Acquire the spinlock, re-verify space, and write the entire frame
atomically.
This ensures that sleeping only happens without any lock held, and
that frames are either fully enqueued or not written at all.
This bug is found by CodeQL static analysis tool (interprocedural
sleep-in-atomic query) and my code review. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix deadlock in jbd2_journal_cancel_revoke()
Commit f76d4c28a46a ("fs/jbd2: use sleeping version of
__find_get_block()") changed jbd2_journal_cancel_revoke() to use
__find_get_block_nonatomic() which holds the folio lock instead of
i_private_lock. This breaks the lock ordering (folio -> buffer) and
causes an ABBA deadlock when the filesystem blocksize < pagesize:
T1 T2
ext4_mkdir()
ext4_init_new_dir()
ext4_append()
ext4_getblk()
lock_buffer() <- A
sync_blockdev()
blkdev_writepages()
writeback_iter()
writeback_get_folio()
folio_lock() <- B
ext4_journal_get_create_access()
jbd2_journal_cancel_revoke()
__find_get_block_nonatomic()
folio_lock() <- B
block_write_full_folio()
lock_buffer() <- A
This can occasionally cause generic/013 to hang.
Fix by only calling __find_get_block_nonatomic() when the passed
buffer_head doesn't belong to the bdev, which is the only case that we
need to look up its bdev alias. Otherwise, the lookup is redundant since
the found buffer_head is equal to the one we passed in. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup: Defer css percpu_ref kill on rmdir until cgroup is depopulated
A chain of commits going back to v7.0 reworked rmdir to satisfy the
controller invariant that a subsystem's ->css_offline() must not run while
tasks are still doing kernel-side work in the cgroup.
[1] d245698d727a ("cgroup: Defer task cgroup unlink until after the task is done switching out")
[2] a72f73c4dd9b ("cgroup: Don't expose dead tasks in cgroup")
[3] 1b164b876c36 ("cgroup: Wait for dying tasks to leave on rmdir")
[4] 4c56a8ac6869 ("cgroup: Fix cgroup_drain_dying() testing the wrong condition")
[5] 13e786b64bd3 ("cgroup: Increment nr_dying_subsys_* from rmdir context")
[1] moved task cset unlink from do_exit() to finish_task_switch() so a
task's cset link drops only after the task has fully stopped scheduling.
That made tasks past exit_signals() linger on cset->tasks until their final
context switch, which led to a series of problems as what userspace expected
to see after rmdir diverged from what the kernel needs to wait for. [2]-[5]
tried to bridge that divergence: [2] filtered the exiting tasks from
cgroup.procs; [3] had rmdir(2) sleep in TASK_UNINTERRUPTIBLE for them; [4]
fixed the wait's condition; [5] made nr_dying_subsys_* visible
synchronously.
The cgroup_drain_dying() wait in [3] turned out to be a dead end. When the
rmdir caller is also the reaper of a zombie that pins a pidns teardown (e.g.
host PID 1 systemd reaping orphan pids that were re-parented to it during
the same teardown), rmdir blocks in TASK_UNINTERRUPTIBLE waiting for those
pids to free, the pids can't free because PID 1 is the reaper and it's stuck
in rmdir, and the system A-A deadlocks. No internal lock ordering breaks
this; the wait itself is the bug.
The css killing side that drove the original reorder, however, can be made
cleanly asynchronous: ->css_offline() is already async, run from
css_killed_work_fn() driven by percpu_ref_kill_and_confirm(). The fix is to
make that chain start only after all tasks have left the cgroup. rmdir's
user-visible side then returns as soon as cgroup.procs and friends are
empty, while ->css_offline() still runs only after the cgroup is fully
drained.
Verified by the original reproducer (pidns teardown + zombie reaper, runs
under vng) which hangs vanilla and succeeds here, and by per-commit
deterministic repros for [2], [3], [4], [5] with a boot parameter that
widens the post-exit_signals() window so each state is reliably reachable.
Some stress tests on top of that.
cgroup_apply_control_disable() has the same shape of pre-existing race:
when a controller is disabled via subtree_control, kill_css() ran
synchronously while tasks past exit_signals() could still be linked to
the cgroup's csets, and ->css_offline() could fire before they drained.
This patch preserves the existing synchronous behavior at that call site
(kill_css_sync() + kill_css_finish() back-to-back) and a follow-up patch
will defer kill_css_finish() there using a per-css trigger.
This seems like the right approach and I don't see problems with it. The
changes are somewhat invasive but not excessively so, so backporting to
-stable should be okay. If something does turn out to be wrong, the fallback
is to revert the entire chain ([1]-[5]) and rework in the development branch
instead.
v2: Pin cgrp across the deferred destroy work with explicit
cgroup_get()/cgroup_put() around queue_work() and the work_fn. v1
wasn't actually broken (ordered cgroup_offline_wq + queue_work order
in cgroup_task_dead() saved it) but the explicit ref removes the
dependency on those non-obvious invariants. Also note the
pre-existing cgroup_apply_control_disable() race in the description;
a follow-up will defer kill_css_finish() there. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl_xcvr: Revert fix missing lock in fsl_xcvr_mode_put()
This reverts commit f51424872760 ("ASoC: fsl_xcvr: fix missing lock in fsl_xcvr_mode_put()").
The original patch attempted to acquire the card->controls_rwsem lock in
fsl_xcvr_mode_put(). However, this function is called from the upper ALSA
core function snd_ctl_elem_write(), which already holds the write lock on
controls_rwsem for the whole put operation. So there is no need to simply
hold the lock for fsl_xcvr_activate_ctl() again.
Acquiring the read lock while holding the write lock in the same thread
results in a deadlock and a hung task, as reported by Alexander Stein. |
| Ubuntu Linux 6.8, 6.17 and 7.0 contain AppArmor SAUCE patches which incorrectly sleep while holding a spinlock in notification handling code. The bug can be triggered by an unprivileged local user and can result in kernel panic or deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/eeh: fix recursive pci_lock_rescan_remove locking in EEH event handling
The recent commit 1010b4c012b0 ("powerpc/eeh: Make EEH driver device
hotplug safe") restructured the EEH driver to improve synchronization
with the PCI hotplug layer.
However, it inadvertently moved pci_lock_rescan_remove() outside its
intended scope in eeh_handle_normal_event(), leading to broken PCI
error reporting and improper EEH event triggering. Specifically,
eeh_handle_normal_event() acquired pci_lock_rescan_remove() before
calling eeh_pe_bus_get(), but eeh_pe_bus_get() itself attempts to
acquire the same lock internally, causing nested locking and disrupting
normal EEH event handling paths.
This patch adds a boolean parameter do_lock to _eeh_pe_bus_get(),
with two public wrappers:
eeh_pe_bus_get() with locking enabled.
eeh_pe_bus_get_nolock() that skips locking.
Callers that already hold pci_lock_rescan_remove() now use
eeh_pe_bus_get_nolock() to avoid recursive lock acquisition.
Additionally, pci_lock_rescan_remove() calls are restored to the correct
position—after eeh_pe_bus_get() and immediately before iterating affected
PEs and devices. This ensures EEH-triggered PCI removes occur under proper
bus rescan locking without recursive lock contention.
The eeh_pe_loc_get() function has been split into two functions:
eeh_pe_loc_get(struct eeh_pe *pe) which retrieves the loc for given PE.
eeh_pe_loc_get_bus(struct pci_bus *bus) which retrieves the location
code for given bus.
This resolves lockdep warnings such as:
<snip>
[ 84.964298] [ T928] ============================================
[ 84.964304] [ T928] WARNING: possible recursive locking detected
[ 84.964311] [ T928] 6.18.0-rc3 #51 Not tainted
[ 84.964315] [ T928] --------------------------------------------
[ 84.964320] [ T928] eehd/928 is trying to acquire lock:
[ 84.964324] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964342] [ T928]
but task is already holding lock:
[ 84.964347] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964357] [ T928]
other info that might help us debug this:
[ 84.964363] [ T928] Possible unsafe locking scenario:
[ 84.964367] [ T928] CPU0
[ 84.964370] [ T928] ----
[ 84.964373] [ T928] lock(pci_rescan_remove_lock);
[ 84.964378] [ T928] lock(pci_rescan_remove_lock);
[ 84.964383] [ T928]
*** DEADLOCK ***
[ 84.964388] [ T928] May be due to missing lock nesting notation
[ 84.964393] [ T928] 1 lock held by eehd/928:
[ 84.964397] [ T928] #0: c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964408] [ T928]
stack backtrace:
[ 84.964414] [ T928] CPU: 2 UID: 0 PID: 928 Comm: eehd Not tainted 6.18.0-rc3 #51 VOLUNTARY
[ 84.964417] [ T928] Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_022) hv:phyp pSeries
[ 84.964419] [ T928] Call Trace:
[ 84.964420] [ T928] [c0000011a7157990] [c000000001705de4] dump_stack_lvl+0xc8/0x130 (unreliable)
[ 84.964424] [ T928] [c0000011a71579d0] [c0000000002f66e0] print_deadlock_bug+0x430/0x440
[ 84.964428] [ T928] [c0000011a7157a70] [c0000000002fd0c0] __lock_acquire+0x1530/0x2d80
[ 84.964431] [ T928] [c0000011a7157ba0] [c0000000002fea54] lock_acquire+0x144/0x410
[ 84.964433] [ T928] [c0000011a7157cb0] [c0000011a7157cb0] __mutex_lock+0xf4/0x1050
[ 84.964436] [ T928] [c0000011a7157e00] [c000000000de21d8] pci_lock_rescan_remove+0x28/0x40
[ 84.964439] [ T928] [c0000011a7157e20] [c00000000004ed98] eeh_pe_bus_get+0x48/0xc0
[ 84.964442] [ T928] [c0000011a7157e50] [c00000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix deadlocks between devlink and netdev instance locks
In the mentioned "Fixes" commit, various work tasks triggering devlink
health reporter recovery were switched to use netdev_trylock to protect
against concurrent tear down of the channels being recovered. But this
had the side effect of introducing potential deadlocks because of
incorrect lock ordering.
The correct lock order is described by the init flow:
probe_one -> mlx5_init_one (acquires devlink lock)
-> mlx5_init_one_devl_locked -> mlx5_register_device
-> mlx5_rescan_drivers_locked -...-> mlx5e_probe -> _mlx5e_probe
-> register_netdev (acquires rtnl lock)
-> register_netdevice (acquires netdev lock)
=> devlink lock -> rtnl lock -> netdev lock.
But in the current recovery flow, the order is wrong:
mlx5e_tx_err_cqe_work (acquires netdev lock)
-> mlx5e_reporter_tx_err_cqe -> mlx5e_health_report
-> devlink_health_report (acquires devlink lock => boom!)
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_recover -> mlx5e_tx_reporter_recover_from_ctx
-> mlx5e_tx_reporter_err_cqe_recover
The same pattern exists in:
mlx5e_reporter_rx_timeout
mlx5e_reporter_tx_ptpsq_unhealthy
mlx5e_reporter_tx_timeout
Fix these by moving the netdev_trylock calls from the work handlers
lower in the call stack, in the respective recovery functions, where
they are actually necessary. |
