| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: firewire: isight: bound the sample count to the packet payload
isight_packet() takes the frame count from the device iso packet and
checks it only against the device claimed iso length.
count = be32_to_cpu(payload->sample_count);
if (likely(count <= (length - 16) / 4))
isight_samples(isight, payload->samples, count);
length is the iso header data_length. It can be up to 0xffff. So the
gate allows a count up to about 16379. isight_samples() then copies
count frames out of payload->samples into the PCM DMA buffer.
payload->samples holds only 2 * MAX_FRAMES_PER_PACKET values. The
device multiplexes two samples per frame. A count past
MAX_FRAMES_PER_PACKET reads past the payload. A count past the buffer
size writes past runtime->dma_area. The smallest PCM buffer is larger
than MAX_FRAMES_PER_PACKET. Bounding the count to MAX_FRAMES_PER_PACKET
keeps both the read and the write in range.
A malicious or faulty Apple iSight on the FireWire bus reaches this
during a normal capture.
Add the MAX_FRAMES_PER_PACKET bound to the gate. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: fix use-after-free on registration failure
Make sure to release the sibling interfaces in case controller
registration fails to avoid use-after-free and double-free when they are
eventually disconnected.
This issue was reported by Sashiko while reviewing a fix for a wakeup
source leak in the btusb probe errors paths. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: fix use-after-free on marvell probe failure
Make sure to stop any TX URBs submitted during Marvell OOB wakeup
configuration on later probe failures to avoid use-after-free in the
completion callback.
This issue was reported by Sashiko while reviewing a fix for a wakeup
source leak in the btusb probe errors paths. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix heap buffer overflow in rtw_cfg80211_set_wpa_ie()
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: Fix UAF of hci_conn_params in add_device_complete
add_device_complete() runs from the hci_cmd_sync_work kworker, which
holds only hci_req_sync_lock and *not* hci_dev_lock. It calls
hci_conn_params_lookup() and then dereferences the returned object
(params->flags) without taking hci_dev_lock:
params = hci_conn_params_lookup(hdev, &cp->addr.bdaddr,
le_addr_type(cp->addr.type));
...
device_flags_changed(NULL, hdev, &cp->addr.bdaddr,
cp->addr.type, hdev->conn_flags,
params ? params->flags : 0);
hci_conn_params_lookup() walks hdev->le_conn_params and is documented to
require hdev->lock. A concurrent MGMT_OP_REMOVE_DEVICE
(remove_device()), which does run under hci_dev_lock, can call
hci_conn_params_free() to list_del() and kfree() the very object the
lookup returned, so the subsequent params->flags read touches freed
memory [0].
Hold hci_dev_lock() across the hci_conn_params_lookup() and the read of
params->flags (and the matching event emission) so the lookup result
cannot be freed by a concurrent remove_device() before it is used,
honouring the locking contract of hci_conn_params_lookup().
[0]: (trailing page/memory-state dump trimmed)
BUG: KASAN: slab-use-after-free in add_device_complete+0x358/0x3d8 net/bluetooth/mgmt.c:7671
Read of size 1 at addr ffff000017ab26c1 by task kworker/u9:8/388
CPU: 1 UID: 0 PID: 388 Comm: kworker/u9:8 Not tainted 7.0.11 #20 PREEMPT
Hardware name: linux,dummy-virt (DT)
Workqueue: hci0 hci_cmd_sync_work
Call trace:
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:499 (C)
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xb4/0xd4 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x118/0x5d8 mm/kasan/report.c:482
kasan_report+0xb0/0xf4 mm/kasan/report.c:595
__asan_report_load1_noabort+0x20/0x2c mm/kasan/report_generic.c:378
add_device_complete+0x358/0x3d8 net/bluetooth/mgmt.c:7671
hci_cmd_sync_work+0x14c/0x240 net/bluetooth/hci_sync.c:334
process_one_work+0x628/0xd38 kernel/workqueue.c:3289
process_scheduled_works kernel/workqueue.c:3372 [inline]
worker_thread+0x7a8/0xac0 kernel/workqueue.c:3453
kthread+0x39c/0x444 kernel/kthread.c:436
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Allocated by task 3401:
kasan_save_stack+0x3c/0x64 mm/kasan/common.c:57
kasan_save_track+0x20/0x3c mm/kasan/common.c:78
kasan_save_alloc_info+0x40/0x54 mm/kasan/generic.c:570
poison_kmalloc_redzone mm/kasan/common.c:398 [inline]
__kasan_kmalloc+0xd4/0xd8 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263 [inline]
__kmalloc_cache_noprof+0x1b0/0x458 mm/slub.c:5385
kmalloc_noprof include/linux/slab.h:950 [inline]
kzalloc_noprof include/linux/slab.h:1188 [inline]
hci_conn_params_add+0x10c/0x4b0 net/bluetooth/hci_core.c:2279
hci_conn_params_set net/bluetooth/mgmt.c:5162 [inline]
add_device+0x5b4/0xa54 net/bluetooth/mgmt.c:7755
hci_mgmt_cmd net/bluetooth/hci_sock.c:1721 [inline]
hci_sock_sendmsg+0x10b4/0x1dd0 net/bluetooth/hci_sock.c:1841
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0xe0/0x128 net/socket.c:742
sock_write_iter+0x250/0x390 net/socket.c:1195
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x66c/0xab0 fs/read_write.c:688
ksys_write+0x1fc/0x24c fs/read_write.c:740
__do_sys_write fs/read_write.c:751 [inline]
__se_sys_write fs/read_write.c:748 [inline]
__arm64_sys_write+0x70/0xa4 fs/read_write.c:748
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x84/0x2a8 arch/arm64/kernel/syscall.c:49
el0_svc_common.constprop.0+0xe4/0x294 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x44/0x5c arch/arm64/kernel/syscall.c:151
el0_svc+0x38/0xac arch/arm64/kernel/entry-common.c:724
el0t_64_sync_handler+0xa0/0xe4 arch/arm64/kernel/entry-common.c:743
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:596
Freed by task 3740:
kasan_save_stack+0x3c/0x64
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
netpoll: fix a use-after-free on shutdown path
There is a use-after-free error on netpoll, which is clearly detected by
KASAN.
BUG: KASAN: slab-use-after-free in _raw_spin_lock_irqsave+0x3b/0x80
Read of size 1 at addr ... by task kworker/9:1
Workqueue: events queue_process
Call Trace:
skb_dequeue+0x1e/0xb0
queue_process+0x2c/0x600
process_scheduled_works+0x4b6/0x850
worker_thread+0x414/0x5a0
Allocated by task 242:
__netpoll_setup+0x201/0x4a0
netpoll_setup+0x249/0x550
enabled_store+0x32f/0x380
Freed by task 0:
kfree+0x1b7/0x540
rcu_core+0x3f8/0x7a0
The problem happens when there is a pending TX worker running in
parallel with the cleanup path.
This is what happens on netpoll shutdown path:
1) __netpoll_cleanup() is called
2) set dev->npinfo to NULL
3) call_rcu() with rcu_cleanup_netpoll_info()
3.1) rcu_cleanup_netpoll_info() tries to cancel all workers with
cancel_delayed_work(), but doesn't wait for the worker to finish
4) and kfree(npinfo);
Because 3.1) doesn't really cancel the work, as the comment says "we
can't call cancel_delayed_work_sync here, as we are in softirq", the TX
worker can run after 4).
Tl;DR: queue_process() is not an RCU reader, it reaches npinfo through
the work item via container_of().
Use disable_delayed_work_sync() to ensure the worker is completely
stopped and prevent any future re-arming attempts. Once npinfo is set
to NULL, senders will bail out and not queue new work. The disable flag
ensures any in-flight re-arming attempts also fail silently.
In the future, we can do the cleanup inline here without needing the
npinfo->rcu rcu_head, but that is net-next material. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Fix next buffer leak in receive_encrypted_standard()
receive_encrypted_standard() allocates next_buffer before checking
whether the number of compound PDUs already reached MAX_COMPOUND. If
the limit check fails, the function returns immediately and the newly
allocated next_buffer is not assigned to server->smallbuf/server->bigbuf,
making it leaked.
Move the MAX_COMPOUND check before allocating next_buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: letsketch: fix UAF on inrange_timer at driver unbind
letsketch_driver does not provide a .remove callback, but
letsketch_probe() arms a per-device timer:
timer_setup(&data->inrange_timer, letsketch_inrange_timeout, 0);
The timer is re-armed from letsketch_raw_event() with a 100 ms
timeout on every pen-in-range report, and its callback dereferences
data->input_tablet to deliver a synthetic BTN_TOOL_PEN release.
letsketch_data is allocated with devm_kzalloc(), and its input_dev
fields are devm-allocated via letsketch_setup_input_tablet(). On
device unbind (USB unplug or rmmod), the HID core runs its default
teardown and devm cleanup frees both letsketch_data and the input
devices. Because no .remove callback exists, nothing drains the
timer first: if raw_event armed it within ~100 ms of the unbind,
the pending timer fires on freed memory. This is a UAF read of
data and of data->input_tablet, followed by input_report_key() /
input_sync() into the freed input_dev.
The same problem can occur on the probe error path: if
hid_hw_start() enabled I/O on an always-poll-quirk device and then
failed, raw_event may have armed the timer before devm releases
data.
Fix by adding a .remove callback that calls hid_hw_stop() first.
hid_hw_stop() synchronously kills the URBs that deliver raw_event(),
so once it returns no path can re-arm the timer. timer_shutdown_sync()
then drains any in-flight callback and permanently disables further
mod_timer() calls. Apply the same timer_shutdown_sync() in the probe
error path so the timer is guaranteed not to outlive data. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: appleir: fix UAF on pending key_up_timer in remove()
appleir_remove() runs hid_hw_stop() before timer_delete_sync().
hid_hw_stop() synchronously unregisters the HID input device via
hid_disconnect() -> hidinput_disconnect() -> input_unregister_device(),
which drops the last reference and frees the underlying input_dev when
no userspace handle holds it open.
key_up_tick() reads appleir->input_dev and calls input_report_key() /
input_sync() on it. The timer is armed from appleir_raw_event() with
a HZ/8 (~125 ms) timeout on every keydown and key-repeat report. If a
key was pressed shortly before the device is disconnected, the timer
can fire after hid_hw_stop() has freed input_dev but before the
teardown drains it.
A simple reorder is not sufficient. Putting the timer drain first
still leaves a window where a USB URB completion (raw_event) running
during hid_hw_stop() can call mod_timer() and re-arm the timer, which
then fires after hidinput_disconnect() has freed input_dev. The same
URB-completion window also lets raw_event() reach key_up(), key_down()
and battery_flat() directly, all of which dereference
appleir->input_dev.
Introduce a 'removing' flag on struct appleir, gated by the existing
spinlock. appleir_remove() sets the flag under the lock and then
shuts down the timer with timer_shutdown_sync(), which both drains any
in-flight callback and permanently disables further mod_timer() calls.
appleir_raw_event() and key_up_tick() bail out early if the flag is
set, so no path can arm or run the timer, or dereference
appleir->input_dev, after remove() has started tearing down.
The keyrepeat and flatbattery branches of appleir_raw_event()
previously called into the input layer without holding the spinlock;
take it now so the flag check is well-defined. This incidentally
closes a pre-existing read-side race on appleir->current_key in the
keyrepeat branch.
This bug is structurally a sibling of commit 4db2af929279 ("HID:
appletb-kbd: fix UAF in inactivity-timer cleanup path") and has been
present since the driver was introduced. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: lg-g15: cancel pending work on remove to fix a use-after-free
lg_g15_data is allocated with devm and holds a work item. The report
handlers schedule that work straight from device input.
lg_g15_event() and lg_g15_v2_event() do it on the backlight cycle key,
and lg_g510_leds_event() does it too. The worker dereferences the
lg_g15_data back through container_of.
The driver had no remove callback and never cancelled the work. So if a
report scheduled the work and the keyboard was then unplugged, devres
freed lg_g15_data while the work was still pending or running, and the
worker touched freed memory. This is a use-after-free. It is reachable
as a race on device unplug.
Add a remove callback that cancels the work before devres frees the
state. g15->work is only initialized for the models that schedule it
(G15, G15 v2, G510). The G13 and Z-10 leave it zeroed, so guard the
cancel on g15->work.func to avoid cancelling a work that was never set
up. The g15 NULL test mirrors the one already in lg_g15_raw_event(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Allow LPM map access from sleepable BPF programs
trie_lookup_elem() annotates its rcu_dereference_check() walks with
only rcu_read_lock_bh_held(). Because rcu_dereference_check(p, c)
resolves to "c || rcu_read_lock_held()", this passes for XDP/NAPI and
classic RCU readers but fails for sleepable BPF programs, which enter
via __bpf_prog_enter_sleepable() and hold only rcu_read_lock_trace().
trie_update_elem() and trie_delete_elem() have the same problem in a
different form: they walk the trie with plain rcu_dereference(), which
asserts rcu_read_lock_held() unconditionally. Both are reachable from
sleepable BPF programs via the bpf_map_update_elem / bpf_map_delete_elem
helpers, and from the syscall path under classic rcu_read_lock(). In
the writer paths the trie is actually protected by trie->lock (an
rqspinlock taken across the walk); we never relied on the RCU read-side
lock to keep nodes alive there.
A sleepable LSM hook that ends up touching an LPM trie therefore
triggers lockdep on debug kernels:
=============================
WARNING: suspicious RCU usage
7.1.0-... Tainted: G E
-----------------------------
kernel/bpf/lpm_trie.c:249 suspicious rcu_dereference_check() usage!
1 lock held by net_tests/540:
#0: (rcu_tasks_trace_srcu_struct){....}-{0:0},
at: __bpf_prog_enter_sleepable+0x26/0x280
Call Trace:
dump_stack_lvl
lockdep_rcu_suspicious
trie_lookup_elem
bpf_prog_..._enforce_security_socket_connect
bpf_trampoline_...
security_socket_connect
__sys_connect
do_syscall_64
This is lockdep-only -- no UAF, since Tasks Trace RCU does serialize
against the trie's reclaim path -- but it spams the console once per
distinct callsite on every debug kernel running a sleepable BPF LSM
that touches an LPM trie, which is increasingly common.
For the lookup path, switch the rcu_dereference_check() annotation
from rcu_read_lock_bh_held() to bpf_rcu_lock_held(), which accepts all
three contexts (classic, BH, Tasks Trace). Other map types already
follow this convention.
For trie_update_elem() and trie_delete_elem(), annotate the walks as
rcu_dereference_protected(*p, 1) -- matching trie_free() in the same
file -- since trie->lock is held across the walk. rqspinlock has no
lockdep_map, so the predicate degenerates to '1' rather than
lockdep_is_held(&trie->lock); the protection is real but not
machine-verifiable. trie_get_next_key() also uses bare
rcu_dereference() but is reachable only from the BPF syscall, which
holds classic rcu_read_lock() before dispatching, so it is left
untouched. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: free iso schedules on failed submit
EHCI and FOTG210 isochronous submits build an ehci_iso_sched before
linking the URB to the endpoint queue, and keep the staged schedule in
urb->hcpriv until iso_stream_schedule() and the link helpers consume it.
If the controller is no longer accessible, or usb_hcd_link_urb_to_ep()
fails, submit jumps to done_not_linked before that handoff happens and
leaks the staged schedule still attached to urb->hcpriv.
Free the staged schedule from done_not_linked when submit fails before
the URB is linked and clear urb->hcpriv after the free.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
EHCI host controller with a USB isochronous device to test with, no
runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: udc: Fix use-after-free in gadget_match_driver
The udc structure acts as the management structure for the gadget,
but their lifecycles are decoupled. A race condition exists where
usb_del_gadget() frees the udc memory (e.g., via mode-switch work)
while gadget_match_driver() concurrently accesses the freed udc memory
(e.g., via configfs), causing a Use-After-Free (UAF) that triggers a
NULL pointer dereference when the freed memory is zeroed:
[39430.908615][ T1171] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[39430.911397][ T1171] pc : __pi_strcmp+0x20/0x140
[39430.911441][ T1171] lr : gadget_match_driver+0x34/0x60
...
[39430.911890][ T1171] usb_gadget_register_driver_owner+0x50/0xf8
[39430.911910][ T1171] gadget_dev_desc_UDC_store+0xf4/0x140
[39430.931308][ T1171] configfs_write_iter+0xec/0x134
[39430.957058][ T1171] Workqueue: events_freezable __dwc3_set_mode
[39430.957287][ T1171] dwc3_gadget_exit+0x34/0x8c
[39430.957304][ T1171] __dwc3_set_mode+0xc0/0x664
Fix this by ensuring the udc structure remains allocated until the
gadget is released. To achieve this, introduce a new
usb_gadget_release() routine to the core. When the gadget is added,
usb_add_gadget() stores the gadget's release routine in the udc
structure and takes a reference to the udc. When the gadget is
released, usb_gadget_release() drops the reference to the udc and
then calls the gadget's release routine. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: idmouse: fix use-after-free on disconnect race
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked") |
| In the Linux kernel, the following vulnerability has been resolved:
USB: ldusb: fix use-after-free on disconnect race
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked") |
| In the Linux kernel, the following vulnerability has been resolved:
USB: iowarrior: fix use-after-free on disconnect
Submitted write URBs are not stopped on close() and therefore need to be
stopped unconditionally on disconnect() to avoid use-after-free in the
completion handler. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: iowarrior: fix use-after-free on disconnect race
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked") |
| In the Linux kernel, the following vulnerability has been resolved:
USB: legousbtower: fix use-after-free on disconnect race
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked") |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Validate SVID index in svdm_consume_modes()
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes(). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: ccg: Fix use-after-free of ucsi on remove
The threaded IRQ handler ccg_irq_handler() calls ucsi_notify_common(),
which on a connector-change event calls ucsi_connector_change() and
schedules connector work. In ucsi_ccg_remove(), ucsi_destroy() frees
uc->ucsi (kfree) before free_irq() is called, so a handler invocation
already in flight may access the freed object after ucsi_destroy().
CPU 0 (remove) | CPU 1 (threaded IRQ)
ucsi_destroy(uc->ucsi) | ccg_irq_handler()
kfree(ucsi) // FREE | ucsi_notify_common(uc->ucsi) // USE
Move free_irq() before ucsi_destroy() in the remove path. It is kept
after ucsi_unregister(): ucsi_unregister() cancels connector work whose
handler issues GET_CONNECTOR_STATUS through ucsi_send_command_common(),
which waits for a completion that is signalled from the IRQ handler, so
the IRQ must stay active until that work has been cancelled.
The probe error path already orders free_irq() before ucsi_destroy().
This bug was found by static analysis. |
