| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tty: abort break signalling on hangup
The break ioctls can race with hangup and end up calling into a tty
driver for a device that is already gone or powered down.
Drivers must handle this race, but TCSBRK and TCSBRKP should still be
aborted to avoid calling back into the driver after a user-controlled
timeout (possibly even after the tty has been reopened).
Note that drivers should disable any break state on shutdown so just
return on hangup (calling break_ctl() again is racy and will most likely
fail for drivers handling the race). |
| In the Linux kernel, the following vulnerability has been resolved:
tty: fix saved termios reset race
Resetting saved termios state on device registration is needed where a
minor number can be reused for an entirely different device and where
the old settings may prevent the port from even being opened (e.g. when
CLOCAL is not set).
Not all TTY drivers guarantee that the minor number is no longer in use
when registering devices however, something which can lead to a
use-after-free when closing a TTY (and saving its termios) races with
re-registration.
Add a new TTY_DRIVER_RESET_SAVED_TERMIOS flag to request that any saved
termios state is reset on registration and only set it for drivers that
make sure that the minor number is no longer in use. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: block2mtd: Fix divide error when erase_size is zero
The erase size is parsed from the "block2mtd" module parameter and can
be set to zero. add_device() then evaluates
if (size % erase_size)
with a zero divisor, which triggers a divide error:
divide error: 0000 [#1] PREEMPT SMP PTI
RIP: 0010:add_device drivers/mtd/devices/block2mtd.c:296 [inline]
RIP: 0010:block2mtd_setup2+0x592/0xda0 drivers/mtd/devices/block2mtd.c:459
Call Trace:
block2mtd_setup+0x27/0xe0 drivers/mtd/devices/block2mtd.c:476
param_attr_store+0x214/0x310 kernel/params.c:589
module_attr_store+0x65/0x90 kernel/params.c:904
kernfs_fop_write_iter+0x3a4/0x540 fs/kernfs/file.c:345
...
Reject a zero erase size before performing the modulo operation so the
existing "erasesize must be a divisor of device size" error path
reports the invalid argument and frees the device. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: drain PS delivery work during station teardown
Removing an AP or mesh station can notify the driver and wake TXQs after
the station has already been removed from the driver, and can update
num_sta_ps and the power-save queues after station cleanup has purged
them.
sta_deliver_ps_frames() tests sta->dead only before it starts delivery. A
worker that passes that test can be delayed while teardown sets sta->dead
and removes the station from the driver; when it resumes it still runs the
full delivery.
The existing cancel_work_sync() sits near the end of
__cleanup_single_sta(), after the final driver state transition and after
PS accounting and queue purging, so it drains the worker only once the
state it has to protect has already changed. Before commit d34ba2168a3c
("mac80211: don't delay station destruction") cleanup was deferred
through the same ordered workqueue as the delivery work, which kept the
two ordered.
Cancel the work after setting sta->dead and before moving the driver
state, and move the existing cancellation to the start of
__cleanup_single_sta(). The first drain closes the driver-lifetime window;
driver callbacks during the remaining state transitions can still queue
drv_deliver_wk through ieee80211_sta_block_awake(), so retain the second
drain at the start of __cleanup_single_sta(). That drain also covers
insertion failures, which reach cleanup without setting sta->dead. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: split cifsFileInfo bitfields to avoid shared-byte RMW races
The invalidHandle, swapfile, oplock_break_cancelled, offload,
and status_file_deleted fields are stored in the same bitfield byte
in struct cifsFileInfo, but are updated in different code paths that
may run simultaneously, and are protected by different locks. Since
bitfield assignments generate byte-level read-modify-write operations,
a modification to one flag can overwrite a concurrent modification to
another flag.
To avoid these races, convert these flags from a bitfield to
separate bool fields. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: stm32-adc: fix possible division by zero in processed channel
In case the conversion has failed or returned zero, processing *val
can lead to a division by zero. Need to check for errors, or converted
value is zero, before processing the data. In case the converted value
is zero, e.g. the Vrefint channel, this should be considered as invalid
in all cases. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: serialize buffer teardown with mode claims
Buffer-mode claims hold mlock to guarantee that the device remains in
buffer mode until the claim is released. Normal buffer updates take
info_exist_lock followed by mlock in iio_update_buffers().
However, iio_device_unregister() disables and deactivates all buffers
without taking mlock. This can invalidate buffer state, including
active_scan_mask, while a buffer-mode claim is held.
Take mlock in iio_disable_all_buffers() so that unregister honors the
mode-claim lifetime guarantee. The info_exist_lock -> mlock ordering
matches iio_update_buffers(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/rmap: fix missing barrier between anon_vma init and vma->anon_vma publish
On arm64 server, we find that a task trying to grab the anon_vma lock
triggers hungtask.
INFO: task main:2354726 blocked for more than 120 seconds.
Tainted: G E 5.10.0-0021.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:main state:D stack: 0 pid:2354726 ppid:2350673 flags:0x00000a01
Call trace:
__switch_to+0x7c/0xbc
__schedule+0x3b4/0x8a0
schedule+0x50/0xe0
rwsem_down_write_slowpath+0x3cc/0x6cc
down_write+0x60/0x260
__anon_vma_prepare+0x6c/0x210
do_anonymous_page+0x258/0x660
handle_pte_fault+0x188/0x214
__handle_mm_fault+0x1b0/0x380
handle_mm_fault+0xf4/0x284
do_page_fault+0x19c/0x494
do_translation_fault+0xcc/0xf8
do_mem_abort+0x48/0xac
el0_da+0x44/0x80
el0_sync_handler+0x88/0xb4
el0_sync+0x160/0x180
After analyzing the vmcore, we found the anon_vma->root->rwsem.count is
-1. There is another anon_vma whose anon_vma->root->rwsem.count is 1, the
anon_vma->root->rwsem.owner shows the lock is held, but the stack of the
task shows the task doesn't hold the anon_vma lock.
After adding more debugging info, we found __anon_vma_prepare() reuses
anon_vma and triggers the UAF of anon_vma->root due to missing memory
barrier, leading to locking and unlocking two different anon_vma->root,
thus leading to an anon_vma will never be unlocked, and another anon_vma
couldn't be locked anymore.
This race requires two adjacent VMAs that are not merged but are
anon_vma-compatible (e.g., they differ in VMA_ACCESS_FLAGS that can be
changed by mprotect()). Two threads fault on each VMA concurrently, both
calling __anon_vma_prepare() with only mmap_lock held for reading.
THREAD A THREAD B
__anon_vma_prepare __anon_vma_prepare
find_mergeable_anon_vma() -> NULL
anon_vma = anon_vma_alloc();
anon_vma->root = anon_vma;
// the two stores may be reordered
vma->anon_vma = anon_vma;
// finds A's anon_vma
anon_vma = find_mergeable_anon_vma(vma);
anon_vma_lock_write(anon_vma);
// may still see the old root
down_write(&anon_vma->root->rwsem);
anon_vma_unlock_write(anon_vma);
// see the new root, never unlock old
up_write(&anon_vma->root->rwsem);
thread A triggers page fault and calls __anon_vma_prepare() to prepare
anon_vma for the faulting vma. __anon_vma_prepare() allocates and
initializes a new anon_vma, and then publishes it to the vma with a plain
store. anon_vma_prepare() only requires the mmap_lock to be held for
reading, so two threads can fault on adjacent VMAs at the same time.
While thread A publishes a new anon_vma, thread B could find the anon_vma
via find_mergeable_anon_vma() and then locks anon_vma->root->rwsem.
The store to anon_vma->root in anon_vma_alloc() and the store to
vma->anon_vma can be reordered. The anon_vma_lock_write() and spin_lock()
only provide acquire semantics, which do not prevent prior stores from
being reordered after them. The release semantics of the corresponding
spin_unlock() and anon_vma_unlock_write() come too late, the store to
vma->anon_vma is already published before they take effect. As a result,
thread B can observe the following order:
vma->anon_vma = anon_vma;
anon_vma->root = anon_vma;
The anon_vma slab is SLAB_TYPESAFE_BY_RCU, so a newly allocated anon_vma
may reuse memory from a previously freed one. The constructor
(anon_vma_ctor) does not reset anon_vma->root, and __put_anon_vma()
doesn't clear it either, so the old root value persists until
anon_vma_alloc() overwrites it. If that store isn't v
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
watchdog: rtd119x: Avoid division by zero
clk_get_rate() could return 0. Avoid a division by zero panic. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix queuing tx_work after workqueue is drained
hci_send_acl(), hci_send_sco() and hci_send_iso() queue hdev->tx_work
unconditionally. They can run from the L2CAP/SCO/ISO socket send path
while hci_dev_close_sync() is draining hdev->workqueue (HCIDEVDOWN
racing with a socket write). Since that queue_work() is not chained
work from the tx_work worker itself, __queue_work() sees the queue
marked __WQ_DRAINING, warns "cannot queue %ps on wq %s", and drops
the work:
WARNING: CPU: 1 PID: 5985 at kernel/workqueue.c:2352 __queue_work
Call Trace:
queue_work_on
l2cap_chan_send
l2cap_sock_sendmsg
...
hci_dev_close_sync() already sets HCI_CMD_DRAIN_WORKQUEUE before
draining, but only hci_cmd_work() and handle_cmd_cnt_and_timer()
check it before queuing. Route the tx_work producers through the
same guard via a shared hci_sched_tx() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
tick/broadcast: Plug clockevents replacement race
朱恺乾 reported and decoded the following race condition when a broadcast
device is replaced:
CPUA CPUB
__tick_broadcast_oneshot_control()
bc = tick_broadcast_device.evtdev;
tick_install_broadcast_device(dev)
clockevents_exchange_device(cur, dev)
shutdown(cur);
detach(cur);
cur->handler = noop;
tick_broadcast_device.evtdev = dev;
tick_broadcast_set_event(bc, next_event); <- FAIL: arms a detached device.
If the original broadcast device has a restricted interrupt affinity mask
and the last CPU in that mask goes offline then the BUG() in
tick_cleanup_dead_cpu() triggers because the clockevent device is not in
detached state.
The reason for this is that tick_install_broadcast_device() is not
serialized vs. tick broadcast operations.
The obvious cure is to serialize tick_install_broadcast_device() with
tick_broadcast_lock against a concurrent tick broadcast operation.
That requires to split clockevents_exchange_device() into two parts, one
which does the exchange, shutdown and detach operation and the other which
drops the module reference count. This is required because the module
reference cannot be dropped while holding tick_broadcast_lock.
Let clockevents_exchange_device() do both operations as before, but let the
broadcast device code take the two step approach and do the device
exchange under tick_broadcast_lock and drop the module reference count
after releasing it. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: prevent race between disconnect() and rtx
Sashiko noted that the two event can race, leading to inconsistent
status. Prevent the race using the synchronous timer stop operation. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix races in cifsd thread creation
The cifsd demultiplex thread can run and access tcp_ses before the parent
thread has finished populating tcp_ses, which the worker thread accesses
locklessly.
Also, the kthread_run macro may start the thread before returning the
thread pointer. Because the pointer is part of the structure that the
thread can access, if the kernel is preempted after the thread is spawned,
but before the thread pointer is populated and the thread attempts to exit,
it will sleep, waiting for a SIGKILL signal.
Fix this by moving creation of the thread to after all of tcp_ses'es
fields are populated, and spawning the thread last, using a split
kthread_create/wake_up_process logic. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: ibss: wait for in-flight TX on disconnect
While leaving an IBSS in ieee80211_ibss_disconnect() mac80211 flushes
stations, turns the carrier off and immediately tells the driver to
leave as well. While there may be synchronize_net() in station flush
and in this code later, packets can still be transmitted due to
cross-CPU race conditions after carrier off is set.
Therefore, it's possible for a race to happen where a TX to the
driver occurs while or after telling it to leave the IBSS. This can
be confusing to drivers, and in the case of iwlwifi leads to an
attempt to use invalid queues.
Move netif_carrier_off() to occur before sta_info_flush() during
IBSS disconnect, and add synchronize_net() if flushing didn't,
so that the synchronize_net() always happens between turning the
carrier off and telling the driver, avoiding this race. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: Make nr_deadline_tasks an atomic_t
The nr_deadline_tasks variable in the cpuset structure was introduced by
commit 6c24849f5515 ("sched/cpuset: Keep track of SCHED_DEADLINE task
in cpusets"). It is reported by sashiko [1] that nr_deadline_tasks
can currently be modified by inc_dl_tasks_cs() under rq->lock and
by cpuset_attach() under cpuset_mutex. So if both updates happen
simultaneously, the nr_deadline_tasks variable can be corrupted leading
to incorrect operations down the road.
Fix that by changing its type to atomic_t so that nr_deadline_tasks
are always atomically updated. This fix patch is a low hanging fruit.
It can handle some of the races between a concurrent sched_setscheduler()
and cpuset_can_attach()/cpuset_attach() calls, but not all of them like
the other issue raised by sashiko [2]. This will be handled hopefully
in a future follow up patch.
[1] https://sashiko.dev/#/patchset/20260626181923.133658-1-longman%40redhat.com
[2] https://sashiko.dev/#/patchset/20260630033344.352702-1-longman%40redhat.com |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Avoid IDR updates while cleaning channels
scmi_cleanup_channels() walks the TX/RX channel IDRs with
idr_for_each() to free transport resources and destroy the dedicated
transport devices before calling idr_destroy().
The destroy callback removed each entry from the same IDR being walked.
That is not needed for this cleanup path, and it is unsafe because
idr_for_each() has not advanced its radix-tree iterator while the
callback is running. Removing the current entry from the callback can
invalidate the iterator state. The callback also cannot be protected by
rcu_read_lock(), because scmi_device_destroy() may sleep.
Leave IDR teardown to the following idr_destroy() call and keep the
callback limited to device destruction. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: guard against division by zero in iwl_dbg_tlv_alloc_fragments
Make sure we don't end-up with a num_frags = 0 situation.
For that, check that the required size is not 0 and put a checker on
num_frags as well. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Fix requested device removal race
scmi_protocol_device_unrequest() drops scmi_requested_devices_mtx while
notifying listeners but continues to retain the per-protocol list head.
When two SCMI drivers for the same protocol unregister concurrently, one
thread can remove the final request and free the list head while the other
is running its notifier. The latter then dereferences the freed list head
after reacquiring the mutex and can free it a second time.
Complete the list and IDR updates, including freeing an empty list head,
before dropping the mutex. Keep the blocking notifier outside the critical
section and retain only the detached request across the callback. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix WARNING in bpf_tracing_link_release
The trampoline could be corrupted by the blindly
'tr->flags = BPF_TRAMP_F_TAIL_CALL_CTX' in verifier.
1. A fexit attached to a tail_call_reachable prog. 'tr->flags' became
'BPF_TRAMP_F_CALL_ORIG | BPF_TRAMP_F_TAIL_CALL_CTX'. And, the
trampoline would poke the target prog's nop insn using jmp insn instead
of call insn.
2. Another fexit loaded with the same tail_call_reachable prog target.
'tr->flags' became 'BPF_TRAMP_F_TAIL_CALL_CTX'.
3. Close the first fexit link. Due to no BPF_TRAMP_F_CALL_ORIG in
'tr->flags', the trampoline will fail to restore the prog's nop insn
using call insn.
[ 3.410719] WARNING: kernel/bpf/syscall.c:3551 at bpf_tracing_link_release+0x53/0x60, CPU#1: test_progs/98
...
[ 3.428793] bpf_link_free+0x58/0x130
[ 3.429293] bpf_link_release+0x23/0x30
Fix the warning by updating 'tr->flags' with '|=' and lock. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: davinci: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_threaded_irq(). During
removal, spi_bitbang_stop() only unregisters the controller; the
subsequent spi_controller_put() then frees the controller together with
its embedded davinci_spi devdata, which is the IRQ handler's dev_id.
The devm_request_threaded_irq() release action (free_irq()), which
drains the handler, does not run until after .remove() returns. A late
or latched interrupt can therefore reach davinci_spi_irq() and
dereference already-freed memory.
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
The clock is acquired with devm_clk_get_enabled(), which is registered
after the IRQ and thus released before it by the devres LIFO order.
Drain the interrupt explicitly with devm_free_irq() before disabling the
controller so that a late interrupt cannot access the registers of a
clock-gated controller.
This issue was found by an in-house static analysis tool. |
